After working with Xiangyu Baoyuan for such a long time on the XG0608C accessories, I have noticed that many customers neglect the routine maintenance of the telescopic arms. In fact, with just a little care, the lifespan of the arm can be significantly extended, and a lot of replacement costs can be saved. Today, I will share a few practical tips that were summarized from actual on-site operations. You can understand them easily.
Daily maintenance: 5 minutes per day, extend the lifespan of the arm.
Maintenance is not complicated. Just spend a few minutes each day before and after your work to check. The key points to focus on are these 3:
1.Cleaning and Dust Removal: After the operation, use a high-pressure air gun to blow away the sand, silt and debris in the gaps and joints of the arm body. These impurities will accelerate wear and tear, especially on muddy construction sites, so they must be thoroughly cleaned.
2. Check lubrication: The hinge area is the most prone to wear and tear. Add lubricating oil to the bushings and pin shafts once a week. Use ordinary industrial lubricating grease; there's no need to purchase expensive ones. The key is to ensure even coverage to prevent dry grinding.
3. Tightening bolts: Before the operation, check the connecting bolts of the arm body. If any looseness is found, tighten them immediately. Long-term vibration can cause the bolts to become loose, which not only affects the operation but also may lead to deformation of the arm body.
In addition, after working in the rainy season or in coastal areas, it is necessary to apply a layer of anti-rust oil to the surface of the armature to prevent corrosion by salt and moisture. This is very crucial and can extend the lifespan by 1-2 years.
Common wear and tear issues: How to identify and how to handle?
The folding arms will inevitably wear out over time. Don't just replace them as soon as there is any sign of wear. First, determine the degree of wear and then handle it in a targeted manner, which will save you money.
1.Wear at the hinge joint (the most common)
The symptoms include abnormal noises when the arm moves and an increase in the gap. Minor wear (gap ≤ 1mm) can be resolved by replacing the bushing. This is a low-cost solution that can be completed in just 10 minutes. If the gap exceeds 2mm, it indicates that the pin shaft is also worn out. In this case, both the pin shaft and the bushing should be replaced to prevent further damage to the arm.
2. Surface rusting and scratches
Minor scratches and rust spots can be cleaned up with sandpaper and then coated with a layer of anti-rust paint; if the rust penetrates the surface and causes depressions, it cannot be used anymore as it is prone to breaking under heavy loads and needs to be replaced with a new arm body. Our XG0608C original arm bodies are all in stock and easy to replace.
3. Arm deformation
Most of the cases are caused by overloading or collisions, manifesting as the inability of the scissor mechanism to open and close smoothly, and inconsistent gaps on both sides. Do not attempt to correct it by yourself. Forcefully bending it back will damage the structural strength, and the subsequent operation will be extremely risky. It is safer to replace the arm body directly.
Avoid these pitfalls: Don't make these three mistakes
Many customers' arms have been damaged prematurely due to improper maintenance. Here are three pitfalls that you must avoid:
Using the wrong type of lubricant: Do not substitute engine oil for grease. Engine oil is prone to leakage and cannot provide long-term lubrication; instead, it will accelerate wear and tear.
Continuing operation after wear: If abnormal noises are detected and the gap is large but the operation continues, the wear will accelerate rapidly. Problems that could have been solved by replacing the bushing can eventually require replacing the entire arm body.
Replace with non-original parts: Buying cheap generic bushings and pins may seem cost-effective, but the mismatch in size leads to a threefold faster wear rate compared to the original factory parts, and it ends up costing more in the long run.
Supporting services of Xiangyu Baoyuan
For the maintenance of the XG0608C scissor arm, we offer a complete set of supporting services to help you relax:
Original factory maintenance parts: Bushings, pin shafts, lubricating grease, etc. are all in stock and perfectly match the arm body. They offer high quality and good value for money.
- Technical guidance: If you are unsure about the extent of the wear, please shoot a video for us. Our professionals will help you assess the situation and guide you through the replacement process.
Emergency replacement: If the arm body is damaged and needs to be replaced urgently, we offer direct delivery from stock. The goods will arrive within the shortest 3 days, ensuring no delay in the project schedule.
In fact, the XG0608C scissor arms are quite durable. As long as you do regular maintenance and promptly address minor damages, they can last for 5 to 8 years without any problems. Instead of waiting for them to break and then spending money to replace them, it's better to spend some time on regular maintenance. This way, you get a higher return on your investment. If you have any maintenance or accessory issues, feel free to contact Xiangyu Baoyuan at any time. We'll handle it for you.
